20 Water Conservation Ideas
AS A HORTICULTURALIST AND AN IRRIGATION CONTRACTOR, I WITNESS
FIRSTHAND THE STAGGERING AMOUNT OF WATER wasted every day in an effort
to maintain a beautiful landscape. As a member of the green industry, I
understand completely my obligation to promote water conservation, as
it is the lifeblood of our industry. As a business owner, I see the
business opportunity available to promote water-efficient products and
techniques. As a human being, I feel the responsibility to educate
people and to encourage everyone to do their small part to help
conserve this valuable resource.
Below are 20 proven ways to conserve water in the landscape. These are some of the recommendations we make daily to encourage water conservation. Each of these ideas presents an opportunity to conserve water and to impact the bottom line of your business. In an effort to cut water consumption, rebates are currently being offered by many municipalities and water purveyors to help cover the costs of these improvements.
At a minimum, all
irrigation systems should have a working rain sensor to suspend
watering in the event of rain. Rain sensors are so effective at saving
water that they are required by law in many states. Soil moisture
probes are an excellent way to shut off the irrigation system when
there is sufficient moisture present in the soil. Wind sensors are
available to prevent watering above a specified wind speed to minimize
water lost to wind drift.
Turf areas and plant beds should always be separated into different zones for efficient watering. Lawns usually require more water than established plantings. If turf and plantings are irrigated on the same zone, then most of the water applied to the plant beds is wasted when the system runs long enough to get sufficient water to the turf. This is an important concept to understand in terms of water conservation and one that is often ignored by irrigation contractors in an effort to cut costs to win the job.
3: Application Devices:
Water is applied by rotary heads,
spray heads, drip emitters, bubblers or micro-sprays. Each of these
devices ap plies water at a different rate, so if they are mixed on the
same zone it is almost impossible to get even coverage throughout the
zone. Mixed application devices on a single zone are a common problem
encountered in the irrigation industry and are often the result of not
understanding precipitation rates.
Watering run times should be adjusted frequently to provide for different watering needs throughout the year as dictated by the growing season and the weather. Decrease the run times during periods of rain and cool weather. Increase the run times during dry periods and for hotter weather. The seasonal-adjust setting available on most irrigation time clocks allows the user to increase or decrease all of the zone run times very easily as a percentage in one simple step.
5: Smart Controllers:
irrigation’s newest innovations, the smart controller, uses weather
data to calculate the amount of water lost from the soil through
evaporation and from the plants through transpiration. These new
controllers adjust the zone run times automatically every day based on local environmental
conditions such as humidity, rainfall, wind, temperature and the amount
of sunshine. Studies have repeatedly shown that the use of smart
controllers can result in water savings of 30 to 60 percent. These new
time clocks are irrigation’s ultimate water conservation tool.
Have an audit performed
to measure the precise water application rate and uniformity of its
distribution for each zone on an irrigation system. These measurements,
coupled with other site information such as exposure, soil type(s) and
plant varieties, allow a base run time to be calculated for each zone
to apply the proper amount of water. The result is a precise watering
schedule with little waste, and a healthier landscape.
7: Operating Pressure:
Adjust the operating
pressure on each irrigation zone to the optimum pressure as recommended
by the manufacturer to prevent water losses through misting at each
head. High pressure causes misting at the nozzle and much of this fine
spray is carried off by the wind and lost. To observe this problem,
look for a cloud of fog around each head when the system is running.
Pressure-regulating valves and heads can be added to eliminate this
Consider the different
microclimates on a site when designing an irrigation system, or
scheduling it to run. Turf in full sun requires more water than turf
growing in shade and plants growing in shade require even less water
than grass in the same environment. Buildings and pavement can reflect
and hold heat generated by the sun. South- and west-facing slopes in
full sun dry faster than north- and east-facing slopes. If turf in full
sun and turf in shade are mixed on the same irrigation zone, the shady
turf will be over-watered when the system is run long enough to meet
the needs of the turf in full sun. All of these factors and more can
have a dramatic effect on the amount of water needed to maintain a
Keeping an irrigation
system in good working condition is one of the best ways to minimize
the inefficient use of water in the landscape. Heads should be adjusted
to prevent overspray onto pavement and other hard surfaces. All of the
heads need to be kept straight and at the right height to water
efficiently. Vegetation should be cleared from around heads to minimize
interference with the spray pattern. Broken heads, malfunctioning
valves, leaking seals and breaks in the piping all need to be
identified and repaired to maximize the use of water.
When designing a new
system, or retrofitting an existing irrigation system, either
micro-sprays or drip should be used for all planting beds. Both of
these methods deliver the water near the rootzone and right to the
plant. This minimizes wind drift and eliminates the problem of water
not reaching its intended target due to plant foliage blocking the
spray. Each of these systems allows the designer to tailor the amount
of water delivered to each plant to meet its individual needs.
Irrigating at night
reduces water loss through evaporation and wind. When watering, apply
only enough water to rewet the root zone and allow the soil to dry out
between watering. This encourages a deep root system and more
drought-tolerant plants. Soil type, microclimate and plant species
should always be considered when setting up an irrigation schedule for
a particular property. Consult your local extension agency for
recommendations if you are not sure.
12: Cycle and Soak:
Many irrigation time
clocks offer a cycle and soak setting that applies the water in several
shorter cycles, allowing it to soak in between cycles. This minimizes
the amount of water lost due to runoff. This can also be accomplished
through the use of multiple start times. Soil composition, infiltration
rate and head type should all be considered when determining if cycle
and soak is necessary.
Mainline breaks and
malfunctioning zone valves are major contributors to wasted water.
Installing a master valve at the water source can reduce water loss by
either of these causes. A master valve shuts off the water supply to an
irrigation system when not in use and automatically turns the water
back on when the system is set to run. When a master valve is used, the
system should be inspected frequently for leaks.
Enough water needs to
be applied on each zone to keep the plants in the area of poorest
coverage alive. This means that over-watering occurs on every zone.
Most spray nozzles have matched precipitation rates to help achieve
even coverage. Correct rotary head nozzles need to be selected for
uniform coverage. A full-circle head should apply four times as much
water as a quarter-circle and half-circle heads should apply twice as
16: Rotary Spray
Nozzles: In recent years, the use of rotary spray nozzles has increased
dramatically due to their efficiency and excellent distribution
uniformity. These nozzles are available from several manufacturers and
can also be used in small areas on windy sites to help overcome the
problems associated with spray heads in windy conditions.
Xeriscape: The use of native and drought-tolerant plants can
dramatically impact the amount of water needed to maintain a healthy
landscape. Mulching plant beds with a heavy layer of mulch,
particularly wood mulch, will help retain the moisture in the soil and
reduce the amount of water needed for the landscape plantings to
EDITOR’S NOTE: David Johnson, owner of Sprinkler Works, Sarasota, Florida, can be reached via email for questions and/or comments at: firstname.lastname@example.org